Buttons and tactile switches are frequently used in many projects involving micro controllers; one of the most frequent issue we met is related to unwanted multiple transitions when the button is pressed once.
Tactile switches, as well as push buttons are mechanical components subject to the problem of bouncing. When a button is connected to a digital GPIO input pin (i.e. an Arduino pin configured as INPUT) we ideally expect that when the button is pressed we get only one high digital signal; unfortunately this rarely happens. During the mechanical movement the physical material vibrates affecting the voltage and the transitions between the On/Off status are not so clear as we usually need. Micro controllers and FPGA are fast enough reading the microseconds oscillations when the button is pressed, resulting multiple readings while apparently we are pressing the button only once.
Read more on Element14 full post: Vintage 555
I have made and used for months the filament roll support based on the mechanics illustrated in the mentioned project but some filament issues have not yet been solved by this tool.
When it is used by 3D printers filament – usually almost robust – is pulled by the extruder while the roll is placed nearby free to rotate. I have observed meaningful differences in the material behaviour depending on the usage level, based on 1Kg filament rolls. A new filament spool flows almost well but the force applied by the extruder should be relatively relevant. The extruder motor (a Nema17 stepper motor) is not damaged but the two gears of the extruder collect particles of the plastic material due the applied force; this requires extruder maintenance after a while to avoid clogging of the filament in the hot end. These particles tends to detach and mix with the clean filament while it is feeding the hot end nozzle increasing clogging problems and a general more frequent nozzle wear; this occurs more frequently with 0.3 mm diameter nozzles.
When the filament roll is half used and more its spirals become smaller and in some environmental conditions the filament tend to break too frequently.
Long print jobs become less reliable; for example I can’t leave the printer working alone for an entire night without controlling it. Thus the idea to make a controlled filament feeder figured a precise series of issues to solve.
- Make the automated engine almost simple and easy to reproduce
- Reduce as much as possible the number of non-3D printable components to make it
- Reduce as much as possible the stress applied to the extruder while printing
- Use a low cost and easy to program micro controller board
- Use the weight load sensor to keep under control che filament consumption and filament feeding
- Manage the environmental noise interfering with the filament weight measures
Also using a single 3D printer we frequently manage more filament rolls (different colors) not all at the same level depending on the print job we are doing. Using an Arduino and the TLE94112EL shield motor controller may result the most reliable and cheaper solution: the board can control up to 6 different brushed motors with simple commands. This Infineon board has its own half bridge motor controller including three different frequencies PWM channels: 80, 100 and 200 Hz. In practice this means running motors sending commands from Arduino keeping the MCU free to other tasks while motors are running.
See more on Element14:
Thanks to Jeremy Cook for featuring the 3D printer filament monitor on Tindie blog!
Prototype is alive
The first prototype is running by about three days and after some revisions on the Arduino software (mostly on the calculation algorithms) it works fine, ready for the public.
- Arduino uno R3
- 5kg max load sensor
- Mx711 chip analog to digital sensor amplifier
- A very small circuit with two buttons and a dip-switch
- 16×2 alphanumeric LCD monochrome display
- Orange LED (shows the load sensor readings when flashing)
Easy to use
The Arduino script has been done to make the use of the tool while 3D printing; it works in a semi-automatic mode and does not need calibration or settings. One of the most interesting aspects is the ability to manage automatically the filament roll also if it is not on start. Then you can change it (e.g. changing the filament colour or material) and the system continue working.
What you should know
Before starting using the filament monitor you need to know the empty roll weight. This is the only fixed variables that can’t be calculated or deducted internally. Knowing this value is easy and you do not need to have an empty roll, obvious! If you weight on a digital scale (possibly one for kitchen more precise than a bigger one) you see that the 1Kg filament roll weight some more, e.g. 120 Gr. This is the weight of your roll that should be setup as the filament tare.
You should also know: Material (PLA or ABS are supported), filament diameter and full roll weight. These values should be preset through the three dip-switches as shown in the following table:
Meaning Off On Material PLA ABS Diameter 1.75mm 3mm Weight 1kg 2kg
- Power-on the support without the filament roll and wait for the display showing Started, The system is self-calibrated to the internal zero point.
- Put the filament roll on the rotating support and press the control button. Arduino calculates the effective weight, deduct the filament tare and enter in the Ready state: remaining meters and percentage of filament as shown too
- Press the control button again; it enters in the Load state and you can start printing!
Pressing the second button you switch between grams and centimeters the constantly updated value of the consumed filament on the second line. The first line instead shows the remaining meters and the used percentage.
Note: as the length in centimeters reach the value 100 (1 meter) the displayed value is shown in meters instead.